BS PD CLC/TR 62125-2008 针对IECTC20的环境报告.电缆

上一篇: ANSI/UL 879-2008 电信号元件
下一篇: BS PD CLC/TR 50454-2008 铝电解电容器应用指南

Product Code:SAE AIR5797
Title:Aircraft Tire Wear Profile Development and Execution for Laboratory Testing
Issuing Committee:A-5c Aircraft Tires Committee
Scope:This SAE Aerospace Information Report (AIR) describes the current process for performing comparative wear testing on aircraft tires in a laboratory environment. This technique is applicable to both radial and bias tires, and is pertinent for all aircraft tire sizes. This AIR describes a technique based upon 驴wear驴 energy. In this technique, side wear energy and drag wear energy are computed as the tire is run through a prescribed test program. The specifics that drive the test setup conditions are discussed in Sections 4 through 7. In general, the technique follows this process:驴 A test profile is developed from measured mechanical property data of the tires under study.驴 Each tire is repeatedly run to the test profile until it is worn to the maximum wear limit (MWL). Several tires, typically 5 to 10, of each tire design are tested.驴 Wear energy is computed for each test cycle and then summed to determine total absorbed wear energy.驴 An index is calculated for each tire design. This is accomplished by dividing the total linear inches of wear at the most worn point into the total wear energy.驴 The indexes are then normalized to provide a comparative wear rate. The described technique is not meant to provide an absolute wear rate or wear index because the technique does not produce results that allow the user to say a tire will last for a specific number of landings. However, it does provide a comparative index. It will make a distinction from one tire design to another by indicating a percentage difference in abrasive wear rate under representative operational conditions. The technique has been demonstrated in a number of test programs and is shown to have an extremely high correlation to field data. Supporting data is included in Section 9.【英文标准名称】:StandardSpecificationforReinforcedConcreteCulvert,StormDrain,andSewerPipe
【原文标准名称】:钢筋混凝土制排水管、雨水管和污水管的标准规范
【标准号】:ASTMC76-2010a
【标准状态】:现行
【国别】:
【发布日期】:2010
【实施或试行日期】:
【发布单位】:美国材料与试验协会(US-ASTM)
【起草单位】:C13.02
【标准类型】:(Specification)
【标准水平】:()
【中文主题词】:圆管;电缆管道;D-荷载;管;加筋混凝土;污水管;雨水道;混凝管(加筋)规范;下水道(混凝土)规范;接头(混凝设备)规范;排水管(混凝土)规范;雨水道/排水混凝管规范
【英文主题词】:circularpipe;culvert;D-load;pipe;reinforcedconcrete;sewerpipe;stormdrain;Concretepipe(reinforced)--specifications;Culvertpipe(concrete)--specifications;Joints(concreteapplications)--specifications;Sewerpipe(concrete)--specifica
【摘要】:1.1Thisspecificationcoversreinforcedconcretepipeintendedtobeusedfortheconveyanceofsewage,industrialwastes,andstormwater,andfortheconstructionofculverts.1.2Thisspecificationistheinch-poundcompaniontoSpecificationC76M;therefore,noSIequivalentsarepresentedinthisspecification.ReinforcedconcretepipethatconformtotherequirementsofC76M,areacceptableunderthisSpecificationC76unlessprohibitedbytheOwner.Note18212;Thisspecificationisamanufacturingandpurchasespecificationonly,anddoesnotincluderequirementsforbedding,backfill,ortherelationshipbetweenfieldloadconditionandthestrengthclassificationofpipe.However,experiencehasshownthatthesuccessfulperformanceofthisproductdependsupontheproperselectionoftheclassofpipe,typeofbeddingandbackfill,andcarethatinstallationconformstotheconstructionspecifications.Theownerofthereinforcedconcretepipespecifiedhereiniscautionedthathemustcorrelatethefieldrequirementswiththeclassofpipespecifiedandprovideinspectionattheconstructionsite.Note28212;AttentioniscalledtothespecificationforreinforcedconcreteD-loadculvert,stormdrain,andsewerpipe(SpecificationC655).
【中国标准分类号】:Q81
【国际标准分类号】:23_040_50
【页数】:11P.;A4
【正文语种】: